• added pan control to delay output
• added drive
• added limiter
• added randomize/clear button
• new gui
*this version doesn’t have backward compatibility,
so if you read old presets, it might sound different
v1.5.1(July 19, 2017)
• fixed samplerate change issue
• added VST3
• improved UI rendering speed
v1.5.5(May 16, 2018)
- Fixed: Coarse knob in VCO doesn’t work correctly
v1.5.51(May 17, 2018)
- Fixed: preset change causes plugin crash(win version only)
The structure of this synth is based on Oberheim SEM.
fixed preset loading issue
fixed delay time sync state not recall correctly
fixed vco frequency displays incorrect value
fixed “go to manual page” linked to wrong page
changed location of settings file
changed location of settings file
fixed automation issue
fixed value display issue.
fixed sync delay time issue
improved interface design
added Mac version
som bug fixes
Changing Preset Folder Location
You can move “HYMONO” folder to where you like.
If you change preset folder location,
next time you need to set preset folder location.
Clicking preset menu button of HY-Mono, popup menu will show up like picture above.
If you select “Change Preset Folder Location“,
preset folder select window will show up like picture below.
You need to select “HYMONO” folder.
And next time HY-Mono will read preset files from that place.
There are two VCO units + Sub/Noise unit.
Each VCO unit can generate saw/pulse waveform.
Bigger knob = coarse(range: -24 to +24 semitones)
Smaller knob = fine(-3 to +3 semitones)
Frequency or Pulse width of oscillator can be modulate by envelope/lfo
Set pulse width of pulse waveform(not affect to saw waveform)
Turn on sync button, oscillator of VCO2 will be synced to oscillator of VCO1.
select waveform of Sub oscillator
You can control oscillator volume in VCF panel.
modulation depth(-100 to 100 %)
modulation source = Env2/LFO
you can control balance of lowpass and highpass
turn on “Bp” button, filter output switch to bandpass.
you can control outputs of VCO section by three knobs at the bottom of VCF panel
ADSD type envelope generator
release rate is defined by decay value
Velo to Envelope
tick the velo box, envelope outputs will be affected by velocity input
LFO unit can generate sine waveform
LFO speed(0.1 to 55 Hz)
phase position of sine waveform
this setting is making sense when “LFO Reset” swith is active.
turn on “S” swith, delay time is synced to host BPM.
delay time can be modulated by ENV1/LFO.
one pole filters for delay line outputs
mix level of delay effect outputs to main signal path
you can control pan position and master output level here.
Midi To CV
You can set PitchBend range here.(+/-1 to +/-12 semitone)
If multiple notes are pressed at the same time,
one of pressed notes will be given priority based on this setting.
Re-Trigger = If this switch is ON, Env1 and Env2 are always triggered by key press.
Filter Track = If this switch is ON, filter cutoff frequency will be affected by played note.
LFO Reset = IF this switch is ON, phase of LFO will be reset by key press.
Midi To Synth Params
You can modulate synth parameters by midi signal.
Source Menu = Velocity, ModWheel, AfterTouch, CC1, CC2
Target Menu = VCO1 Freq, VCO2 Freq, VCF Cf, VCA Amp, Pan, Delay Time
Knob = mod depth(-100~+100%)
You can transpose incoming midi notes.(-2 ~ +2 octave)
ON/OFF Swith = portamento on/off
Knob = portamento time
Ticked panels will be included randomize.
In this case, params of vco1, vcf, env2 and lfo will be randomized.
Re-Size Plugin Window
You can re-size plugin window by pulling bottom right of the plugin window.